You're viewing a previously published revision of this guide.  View latest revision

Older
Jun 06, 2020 - 02:06:27
Nov 15, 2021 - 11:11:17 Nov 15, 2021 - 11:11:59 Nov 15, 2021 - 11:11:32 Aug 08, 2021 - 05:08:44 Aug 08, 2021 - 05:08:33 Dec 27, 2020 - 05:12:23 Dec 27, 2020 - 05:12:00 Jul 19, 2020 - 08:07:29 Jul 19, 2020 - 07:07:43 Jun 20, 2020 - 12:06:13 Jun 19, 2020 - 07:06:54 Jun 15, 2020 - 06:06:06 Jun 15, 2020 - 06:06:30 Jun 15, 2020 - 06:06:58 Jun 15, 2020 - 06:06:28 Jun 15, 2020 - 06:06:45 Jun 15, 2020 - 06:06:58 Jun 15, 2020 - 06:06:22 Jun 15, 2020 - 06:06:17 Jun 15, 2020 - 09:06:09 Jun 14, 2020 - 11:06:14 Jun 14, 2020 - 11:06:41 Jun 14, 2020 - 11:06:51 Jun 14, 2020 - 10:06:47 Jun 14, 2020 - 10:06:01 Jun 14, 2020 - 10:06:32 Jun 14, 2020 - 10:06:10 Jun 14, 2020 - 10:06:16 Jun 14, 2020 - 10:06:54 Jun 14, 2020 - 10:06:22 Jun 14, 2020 - 10:06:33 Jun 12, 2020 - 06:06:35 Jun 07, 2020 - 08:06:35 Jun 07, 2020 - 08:06:32 Jun 07, 2020 - 08:06:43 Jun 07, 2020 - 08:06:22 Jun 06, 2020 - 03:06:04 Jun 06, 2020 - 03:06:49 Jun 06, 2020 - 03:06:26 Jun 06, 2020 - 03:06:53 Jun 06, 2020 - 03:06:40 Jun 06, 2020 - 02:06:12 Jun 06, 2020 - 02:06:52 Jun 06, 2020 - 02:06:31 Jun 06, 2020 - 02:06:33 Jun 06, 2020 - 02:06:46 Jun 06, 2020 - 02:06:35 Jun 06, 2020 - 02:06:27 Jun 06, 2020 - 01:06:37 Jun 06, 2020 - 01:06:55 Jun 06, 2020 - 01:06:16 Jun 06, 2020 - 01:06:52 Jun 06, 2020 - 01:06:36 Jun 06, 2020 - 01:06:23 Jun 06, 2020 - 01:06:41
Newer

O) Electronics

Written By: Tony Akens (and one other contributor)
  • Comments: 17
  • Favorites: 0
  • Completions: 10

Difficulty

Moderate

Steps

3

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

    • THE RAILCORE IS A “DIY” PROJECT - BUILD SAFE, BUILD SMART, AND BE RESPONSIBLE.

    • BUILD AT YOUR OWN RISK

    • WHEN IN DOUBT, DOUBLE CHECK THINGS.

    • 3D PRINTERS CAN GET VERY HOT, USE COMMON SENSE AND QUALITY COMPONENTS.

    • If you need help find us at the RailCore Facebook page, or RailCore Discord channel. Both are linked from RailCore.org

  2. Attach the PSU using (4) M4 x 10mm Button Head Bolts. The bolts go through holes in the right panel, and into the back of the PSU.

    • Attach the PSU using (4) M4 x 10mm Button Head Bolts. The bolts go through holes in the right panel, and into the back of the PSU.

    • Be sure to install the PSU so the wiring terminals are to the bottom of the printer.

  3. Install the SSR as shown.

    • Install the SSR as shown.

    • Each hole is held in place using (1) m3 x 10mm Button Head Bolt.

    • Use a washer both on the SSR side, and on the back of the panel.

    • Fasten with an m3 Washer

Author

with 1 other contributor

Tony Akens

Member since: 10/26/19

12,131 Reputation

21 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 2

Past 30 Days: 6

All Time: 2,167