You're viewing a previously published revision of this guide. View latest revision

Jun 06, 2020 - 01:06:37

Nov 15, 2021 - 11:11:17 Nov 15, 2021 - 11:11:59 Nov 15, 2021 - 11:11:32 Aug 08, 2021 - 05:08:44 Aug 08, 2021 - 05:08:33 Dec 27, 2020 - 05:12:23 Dec 27, 2020 - 05:12:00 Jul 19, 2020 - 08:07:29 Jul 19, 2020 - 07:07:43 Jun 20, 2020 - 12:06:13 Jun 19, 2020 - 07:06:54 Jun 15, 2020 - 06:06:06 Jun 15, 2020 - 06:06:30 Jun 15, 2020 - 06:06:58 Jun 15, 2020 - 06:06:28 Jun 15, 2020 - 06:06:45 Jun 15, 2020 - 06:06:58 Jun 15, 2020 - 06:06:22 Jun 15, 2020 - 06:06:17 Jun 15, 2020 - 09:06:09 Jun 14, 2020 - 11:06:14 Jun 14, 2020 - 11:06:41 Jun 14, 2020 - 11:06:51 Jun 14, 2020 - 10:06:47 Jun 14, 2020 - 10:06:01 Jun 14, 2020 - 10:06:32 Jun 14, 2020 - 10:06:10 Jun 14, 2020 - 10:06:16 Jun 14, 2020 - 10:06:54 Jun 14, 2020 - 10:06:22 Jun 14, 2020 - 10:06:33 Jun 12, 2020 - 06:06:35 Jun 07, 2020 - 08:06:35 Jun 07, 2020 - 08:06:32 Jun 07, 2020 - 08:06:43 Jun 07, 2020 - 08:06:22 Jun 06, 2020 - 03:06:04 Jun 06, 2020 - 03:06:49 Jun 06, 2020 - 03:06:26 Jun 06, 2020 - 03:06:53 Jun 06, 2020 - 03:06:40 Jun 06, 2020 - 02:06:12 Jun 06, 2020 - 02:06:52 Jun 06, 2020 - 02:06:31 Jun 06, 2020 - 02:06:33 Jun 06, 2020 - 02:06:46 Jun 06, 2020 - 02:06:35 Jun 06, 2020 - 02:06:27 Jun 06, 2020 - 01:06:37 Jun 06, 2020 - 01:06:55 Jun 06, 2020 - 01:06:16 Jun 06, 2020 - 01:06:52 Jun 06, 2020 - 01:06:36 Jun 06, 2020 - 01:06:23 Jun 06, 2020 - 01:06:41

Newer

O) Electronics

Written By: Tony Akens (and one other contributor)

Comments: 17
Favorites: 0
Completions: 10

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Step 1 Safety

THE RAILCORE IS A “DIY” PROJECT - BUILD SAFE, BUILD SMART, AND BE RESPONSIBLE.
BUILD AT YOUR OWN RISK
WHEN IN DOUBT, DOUBLE CHECK THINGS.
3D PRINTERS CAN GET VERY HOT, USE COMMON SENSE AND QUALITY COMPONENTS.
If you need help find us at the RailCore Facebook page, or RailCore Discord channel. Both are linked from RailCore.org

Step 2

Attach the PSU using (4) M4 x 10mm Button Head Bolts. The bolts go through holes in the right panel, and into the back of the PSU.

Attach the PSU using (4) M4 x 10mm Button Head Bolts. The bolts go through holes in the right panel, and into the back of the PSU.
Be sure to install the PSU so the wiring terminals are to the bottom of the printer.