You're viewing a previously published revision of this guide. View latest revision

Jan 26, 2020 - 12:01:58

Dec 29, 2020 - 11:12:00 Aug 23, 2020 - 08:08:13 Aug 23, 2020 - 08:08:51 Aug 23, 2020 - 08:08:46 Aug 23, 2020 - 05:08:56 Aug 23, 2020 - 05:08:07 Jul 12, 2020 - 10:07:06 Jul 12, 2020 - 10:07:06 Jul 12, 2020 - 10:07:55 Jul 12, 2020 - 10:07:50 Jul 12, 2020 - 10:07:43 Jul 12, 2020 - 10:07:41 Jul 12, 2020 - 10:07:41 Jul 11, 2020 - 08:07:22 Jun 15, 2020 - 04:06:36 Jun 15, 2020 - 04:06:47 Jun 15, 2020 - 04:06:46 Jun 05, 2020 - 02:06:59 Jun 05, 2020 - 01:06:34 Jun 05, 2020 - 01:06:11 May 06, 2020 - 05:05:08 May 06, 2020 - 05:05:54 May 06, 2020 - 05:05:48 May 06, 2020 - 05:05:43 May 06, 2020 - 05:05:31 May 06, 2020 - 05:05:09 Mar 22, 2020 - 11:03:21 Jan 26, 2020 - 12:01:05 Jan 26, 2020 - 12:01:51 Jan 26, 2020 - 12:01:25 Jan 26, 2020 - 12:01:14 Jan 26, 2020 - 12:01:02 Jan 26, 2020 - 12:01:04 Jan 26, 2020 - 12:01:58 Jan 26, 2020 - 12:01:28 Jan 26, 2020 - 12:01:23 Jan 26, 2020 - 12:01:58 Jan 26, 2020 - 12:01:24 Jan 26, 2020 - 12:01:13 Jan 07, 2020 - 11:01:49 Jan 07, 2020 - 11:01:32 Jan 07, 2020 - 11:01:55 Oct 28, 2019 - 09:10:59 Oct 27, 2019 - 06:10:54 Oct 27, 2019 - 01:10:39 Oct 26, 2019 - 03:10:19 Oct 26, 2019 - 02:10:36 Oct 26, 2019 - 02:10:06 Oct 26, 2019 - 02:10:58 Oct 26, 2019 - 02:10:23 Oct 26, 2019 - 01:10:19 Oct 26, 2019 - 01:10:18 Oct 26, 2019 - 01:10:18 Oct 26, 2019 - 01:10:18 Oct 26, 2019 - 01:10:18 Oct 26, 2019 - 01:10:18 Oct 26, 2019 - 01:10:49

Newer

G) Sides Installation

Written By: Tony Akens (and 2 other contributors)

Comments: 13
Favorites: 0
Completions: 23

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Step 1 Bottom Panel Installation

Flip the printer frame upside down, to install the bottom panel first.

It's important the two holes are on the same side as the two Z towers, and the "shiny" side of the panel faces out.

Flip the printer frame upside down, to install the bottom panel first.
It's important the two holes are on the same side as the two Z towers, and the "shiny" side of the panel faces out.
It's easiest to start by lining up the bolts close to where they'll need to be. Then start from one corner and work your way along the sides. Needle nose pliers can help to line the bolts up with the holes.

Step 2 Back Panel Installation

Lay the printer front down on some blocks to protect the bolts.

Lay the printer front down on some blocks to protect the bolts.
Install the back panel using (20) M3 Nylon Lock Nuts, in the same method as before. Do not fully tighten the nuts yet.