You're viewing a previously published revision of this guide.  View latest revision

Older
Feb 05, 2022 - 07:02:44
Apr 04, 2022 - 07:04:42 Apr 04, 2022 - 07:04:27 Apr 04, 2022 - 06:04:30 Mar 31, 2022 - 09:03:28 Mar 31, 2022 - 09:03:11 Mar 31, 2022 - 08:03:57 Mar 31, 2022 - 08:03:14 Mar 31, 2022 - 08:03:02 Mar 31, 2022 - 08:03:51 Mar 31, 2022 - 08:03:16 Mar 31, 2022 - 08:03:57 Mar 31, 2022 - 08:03:18 Mar 31, 2022 - 08:03:15 Mar 31, 2022 - 08:03:05 Mar 31, 2022 - 08:03:41 Mar 31, 2022 - 08:03:32 Feb 05, 2022 - 08:02:02 Feb 05, 2022 - 08:02:29 Feb 05, 2022 - 08:02:04 Feb 05, 2022 - 08:02:54 Feb 05, 2022 - 08:02:26 Feb 05, 2022 - 08:02:36 Feb 05, 2022 - 08:02:37 Feb 05, 2022 - 08:02:15 Feb 05, 2022 - 08:02:01 Feb 05, 2022 - 08:02:14 Feb 05, 2022 - 08:02:17 Feb 05, 2022 - 08:02:07 Feb 05, 2022 - 08:02:37 Feb 05, 2022 - 08:02:17 Feb 05, 2022 - 08:02:13 Feb 05, 2022 - 08:02:31 Feb 05, 2022 - 08:02:07 Feb 05, 2022 - 08:02:00 Feb 05, 2022 - 08:02:10 Feb 05, 2022 - 08:02:01 Feb 05, 2022 - 08:02:45 Feb 05, 2022 - 08:02:36 Feb 05, 2022 - 08:02:12 Feb 05, 2022 - 07:02:35 Feb 05, 2022 - 07:02:35 Feb 05, 2022 - 07:02:58 Feb 05, 2022 - 07:02:49 Feb 05, 2022 - 07:02:15 Feb 05, 2022 - 07:02:44 Feb 05, 2022 - 07:02:29 Feb 05, 2022 - 07:02:18 Feb 05, 2022 - 07:02:29
Newer

D) Bottom Extrusions Assembly

Written By: Ben Withem (and one other contributor)
  • Comments: 0
  • Favorites: 0
  • Completions: 1

Difficulty

Moderate

Steps

1

Time Required

Suggest a time??

Sections

1

Flags

3

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

User-Contributed Guide

User-Contributed Guide

This guide is not managed by the site's staff.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

Introduction

It's assumed that you're building a kit from Filastruder, and you've completed all previous sections. At the end of this section you should have a "bottom extrusions" assembly together for your RailCore frame.

  1. Layout Bottom Frame as shown. Note that the corner cubes should have a small hole facing up.

    • Layout Bottom Frame as shown. Note that the corner cubes should have a small hole facing up.

    • It is a good idea to mark each extrusion with a bit of masking tape on top, indicating which extrusion it is.

Author

with 1 other contributor

Ben Withem

Member since: 1/2/22

10,412 Reputation

19 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 1

All Time: 174